Відео

Difficulty with the re-insertion of the small pin and how you were honest about that part of the process makes this a very relatable piece of work. Loved it! OH and this is probably what's wrong with my boat and now, after your demonstration, I think I got this!

Thank you sir!!

Great vídeo

😂😂😂 dude I laughed this whole video. Great job thanks for the FUCKING learning experience.

Hi Thanks for video, do you have a part number for that seal?

Excellent video. I just did this job on an Volvo Penta MS4b gearbox after watching. Essentially it's exactly the same and easy if you take your time. Use Volvo genuine parts they are much better quality than the seals that failed.

Thanks. We would be in real trouble if that roll pin didn't come out so easily ! That selector paddle can be installed the wrong way. If so, the plate will not land and will show resistance. On the Volvo MS and MSB gearboxes, the paddle can drop into the gearbox and needs fished with a magnet. Be careful not to lose the spring or the paddle if there is a deep bilge below the motor !! I wonder what size the seal is on the MS and MSB gearboxes.

Hello, I came across this post as I'm dealing with and researching this same, shift shaft seal, issue now. I'm confident I will be able to replace this myself but am wondering if you could tell me, what are the symptoms of performance when this seal gets a leak? I've noticed lately, reverse is not engaging right away and now forward is acting the same. I have to give it a little throttle before it will engage. Also, intermittently, when I increase throttle to get on plane, the engine seems to bog and won't increase speed. After a couple of tries, I can get it to react properly. Are these different issues or could this happen due to a bad seal? Maybe I'm totally off base all together. Thanks for any input. I have twin 2001 volvo penta 5.7gsi motors.

Muy bien tu trabajo y explicado

Fuck at seal

Thanks for posting a great video 👍🏻big help …have this to do on my outdrive as leaking from same seal cheers

After watching it, very easy work no tools needed. Replaced the seal on my xdp within 5 minutes

That was a fucking awesome video!

I have the same motor. How do you access the shift rod coupling? Thank you.

Please I bought Volvo penta AQ 240A boat 1987 model I need mechanic to fix it for me at Toronto

I see we seem to use the same vocabulary when working on mechanical things. One of the most informative and funny presentations I've seen on a lower end rebuild. Always nice to see a customer rescue job brought back to life. Good stuff!

Jejejejejejeje

S'il vous plaît qu'elle l'année cette moteur?

HI , if i can ask you a question. does the shift cable have to be in the nuetral or forward position when putting the drive back? or taking it down for that matter. Thank you

For anyone doing this themselves...please consider the following; the direction of the clutch dog is critical. This guy does not show it, not sure he knows or not, or if he just forgot to show us. Its really essential however, and I just did this same procedure today on an 86 johnson 28. Same exact foot as this johnyrude. The clutch dog has a groove in it on one side, that side must face the forward drive gear. if you don't know which gear that is, well its the one in the back, or the one furthest away from the prop. This is key, because omc cut those dawg teeth at slightly diff angles in order to mesh properly. if you install it backwards, it may work, but it may also slip outta gear and eventually tear up the dog pawls. If you forget this, its easy enough to tell which way to install, just looking at the wear patterns and mating them to the corresponding wear patterns on the gears. Only one side of the pawl should have any wear. if it has never been reversed, and also assuming it was installed correct the first time, and not already slipping. Thats number one. And no offence to the creator, I actually really appreciate the video. Thank you for takin the time. Number 2, however, I have to tell you the other booboo I saw. And correct me, please if I'm wrong, but Idk how this foot is not gonna take water on, the way he sealed her up. That spaghetti string seals the outter most edges of the foot clam shell(skeg) right? Ok, good. However, the bolt holes run inside of that race for the spaghetti....So, they are not sealed at the top, under the head, so what is keeping H2O from seeping in past the bolt heads and into the foot? Nothing!!!! Also, using no sealant on the clamshell is so brave. Especially where the front hub meets the case. How can water not leak into there without some silly silicone?? Please do not forget these critical steps, because it will only lead to cool whip milkshake in the bottom foot, and nobody wants that.

Hola amigo, excelente video, una pregunta cuanto mide el drive shaft de ese motor, Gracias.

excellent..thank you.

What seal driver did you use

Dang, these lowers look a lot easier to work on than the later models where you can’t separate the gear case. Don’t need a special tool to pull the propshaft housing or have to deal with that deeply recessed snap ring. Im sure that the later ones save mfgr money, have smaller hub diameter and save some water drag from screw holes though

Super honest

That came out real nice.

This is exactly what I wanted to see. Thanks for your honesty. Dang those pencil lines, man.

I just did a reseal and water pump on a 25 evenrude. It had a solid gear housing.

Would the Bravo 1 SZ Be a reliable leg for a cummins 6bt running 200 hp

Thanks for sharing have the same outboard! Awesome work!

Beautiful video. I have a 2007 Volvo SX-A outdrive and last time on the water it refused to go back into neutral. I had to trickle back into the dock and turn it off in gear. I figured shift cable was bad but I disconnected the linkage and I was able to shift smoothly at the control arm with it disconnected from the drive. I checked the service records and it looks like last year the Shift Shaft was sealed just like the video you have attached for the same issue. I was able to tap the shift mechanism lightly with a hammer and move it back in neutral for now but its very stiff. Would you recommend doing this repair a second time and seeing if it fixes the issue or would you guess there is a bigger problem like a cone clutch issue etc?

Great video, and I just Love how you cuz yourway through progress!

hello rock star can you call me 773 968 78 70

Hi ROCKSTAR 791, very much appreciated taking the time making these videos and sharing your knowledge. I have a concern on my VP SX-M outdrive. I recently replaced the oil but i was aware of the level side screw hole. and because of it I didnt put enogh oil in the unit. I took the boat out for a couple of hours. and notice noise coming the outdrive. it will come and go. so i decided to pull boat out and check level i was 30 oz low. now i have metal shaving at the magnet. please advice. I could pass on email to discuss the matter. I really appriciate your help. thank you Sir.

TK!S!!!!!

TK!S!!!!!

Perfect video and perfect explanation. It helped me for fixing a part of my outdrive SX . Thanks a lot .

What building or floor or room number were you in? I'd like to request something similar from our travel agent. Thanks

Thanks. great video

TERRIBLE ....THE CAMERA IS NOT ON THE REPAIR...PARTS FLYING OFF FROM EVERY WHERE....REDOOOOO IT.

Say it with me, I Love My Job! I Love My Job! Boy, Jesus saves and once you accept Him little things like a customer that got in over his head won’t bother you so much! It’s just job putting together an inanimate object. Relax, you’ll be better off:-)

Excellent video, by what is obviously a great mechanic. Thank you for this info. It will help me with my DP Drive work.

Great video. Thanks for sharing

Acting like he had to do the job. Dont like it dont take the job.

what a hot mess. Why not try a heat gun?

Thank you very much for explaining things, can I have a link for your second video as my sx-m mixing water with oil I have pressure test it no leak but still water mixing with the oil any thought what look for or what to replace?

Very informative! Exactly what I was after, thanks!

Where do you buy the seal?

6:22 it looks really good . i am watching this cause iwonder to strip my Cort Evl Z4

Can you tell me were the water intake is